Exmark eXmark Ultra VAC Lazer Z User Manual download pdf (Page 33)

- 28 -

NOTE: The axle positions are in 1/2" increments and the large

caster spacers are 1/2" thick. Therefore, by adjusting the same

number of 1/2" caster spacers as axle hole positions the blades

will retain the same front-to-back tip (rake).

CUTTING HEIGHT ADJUSTMENT (1" to 4 1/4")

AXLE

POSITION

(FIG. 10)

NO. OF SPACERS

BELOW CASTER

1/2" 3/16"

NUMBER OF 1/4" BLADE SPACERS

BELOW

SPINDLE

4 3 2 1 0

A 0 0 1" 1 1/4" 1 1/2" 1 3/4" 2"

A 0 1 1 1/8" 1 3/8" 1 5/8" 1 7/8" 2 1/8"

A 1 0 1 3/8" 1 5/8" 1 7/8" 2 1/8" 2 3/8"

B 0 1 1 3/8" 1 5/8" 1 7/8" 2 1/8" 2 3/8"

B 1 0 1 5/8" 1 7/8" 2 1/8" 2 3/8" 2 5/8"

B 1 1 1 3/4" 2" 2 1/4" 2 1/2" 2 3/4"

B 2 0 2" 2 1/4" 2 1/2" 2 3/4" 3"

C 1 1 1 7/8" 2 1/8" 2 3/8" 2 5/8" 2 7/8"

C 2 0 2 1/8" 2 3/8" 2 5/8" 2 7/8" 3 1/8"

C 2 1 2 1/4" 2 1/2" 2 3/4" 3" 3 1/4"

C 3 0 2 ½" 2 3/4" 3" 3 1/4" 3 1/2"

D 2 1 2 3/8" 2 5/8" 2 7/8" 3 1/8" 3 3/8"

D 3 0 2 1/2" 2 3/4" 3" 3 1/4" 3 1/2"

D 3 1 2 3/4" 3" 3 1/4" 3 1/2" 3 3/4"

D 4 0 3" 3 1/4" 3 1/2" 3 3/4" 4"

E 3 1 2 7/8" 3 1/8" 3 3/8" 3 5/8" 3 7/8"

E 4 0 3 1/8" 3 3/8" 3 5/8" 3 7/8" 4 1/8"

E 4 1 3 1/4" 3 1/2" 3 3/4" 4" 4 1/4"

IMPORTANT: To achieve the highest quality of cut, the blades

should be level with the ground, or tipped slightly down at

the front.

5.2.3 Transmission belt adjustment.

a) Stop engine and remove spark plug wire(s).

b) To tighten transmission belt, loosen the 3/8" nyloc

nut on transmission belt idler pulley. Slide bolt

inward in slot and retighten nyloc nut.

c) When properly adjusted, the belt should have 1/2" of

deflection with three pounds of pressure on the belt

midway between the transmission and engine pulley.

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 43 44

Comments to this Manuals

No comments

Exmark eXmark Ultra VAC Lazer Z User Manual Page 33

Comments to this Manuals

Related products and manuals for Lawnmowers Exmark eXmark Ultra VAC Lazer Z